material safety data sheet revision number: 001.0 issue date: 08/24/2011 idh number: 1188169 product name: eccobond 45 clr 1# individual page 1 of 5 1. product and company identification product name: eccobond 45 clr 1# individual idh number: 1188169 product type: epoxy resin region: united states company address: contact information: henkel electronic materials llc 14000 jamboree road irvine, ca 92606 telephone: 1.888.9.henkel (1.888.943.6535) medical emergency phone: poison control center 1-877-671-4608 (toll free) or 1-303-592-1711 transport emergency phone: chemtrec 1-800-424-9300 (toll free) or 1-703-527-3887 internet: www.henkelna.com 2. hazards identification emergency overview hmis: physical state: liquid health: 2 color: colorless to light yellow flammability: 1 odor: slight physical hazard: 0 personal protection: see msds section 8 warning : causes eye and skin irritation. may cause allergic skin reaction. may cause respiratory tract irritation. relevant routes of exposure: skin, inhalation, eyes potential health effects inhalation: may cause respiratory tract irritation. skin contact: causes skin irritation. this product may cause an allergic skin reaction. eye contact: causes eye irritation. ingestion: not expected under normal conditions of use. may cause gastrointestinal tract irritation if swallowed. existing conditions aggravated by exposure: eye, skin and respiratory disorders. this product is considered hazardous under 29 cfr 1910.1200 (hazard communication). see section 11 for additional toxicological information. 3. composition / information on ingredients hazardous components cas number % epoxy resin proprietary 60 - 100 4. first aid measures inhalation: move to fresh air. if not breathing, give artificial respiration. if breathing is difficult, give oxygen. get medical attention. skin contact: immediately flush skin with plenty of water (using soap, if available). remove contaminated clothing and footwear. wash clothing before reuse. if symptoms develop and persist, get medical attention.
idh number: 1188169 product name: eccobond 45 clr 1# individual page 2 of 5 eye contact: rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes. get medical attention. ingestion: do not induce vomiting unless directed to do so by medical personnel. never give anything by mouth to an unconscious person. get medical attention. 5. fire fighting measures flash point: > 200 c (> 392f) supplier method autoignition temperature: not available. flammable/explosive limits - lower: not available. flammable/explosive limits - upper: not available. extinguishing media: water spray (fog), foam, dry chemical or carbon dioxide. special firefighting procedures: wear self-contained breathing apparatus and full protective clothing, such as turn-out gear. in case of fire, keep containers cool with water spray. unusual fire or explosion hazards: closed containers may rupture (due to build up of pressure) when exposed to extreme heat. hazardous combustion products: oxides of carbon, oxides of nitrogen, irritating organic vapors. 6. accidental release measures use personal protection recommended in section 8, isolate the hazard area and deny entry to unnecessary and unprotected personnel. environmental precautions: do not allow product to enter sewer or waterways. clean-up methods: evacuate and ventilate spill area; dike spill to prevent entry into water system; wear full protective equipment during clean-up. soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). store in a partly filled, closed container until disposal. 7. handling and storage handling: use only with adequate ventilation. prevent contact with eyes, skin and clothing. do not breathe vapor and mist. wash thoroughly after handling. refer to section 8. storage: keep in a cool, well ventilated area away from heat, sparks and open flame. keep container tightly closed until ready for use. for information on product shelf life, please review labels on container or check the technical data sheet. 8. exposure controls / personal protection employers should complete an assessment of all workplaces to determine the need for, and selection of, proper exposure controls and protective equipment for each task performed. hazardous components acgih tlv osha pel aiha weel other epoxy resin none none none none engineering controls: provide adequate local exhaust ventilation to maintain worker exposure below exposure limits. respiratory protection: use niosh approved respirator if there is potential to exceed exposure limit(s).
idh number: 1188169 product name: eccobond 45 clr 1# individual page 3 of 5 eye/face protection: safety goggles or safety glasses with side shields. full face protection should be used if the potential for splashing or spraying of product exists. safety showers and eye wash stations should be available. skin protection: use impermeable gloves and protective clothing as necessary to prevent skin contact. 9. physical and chemical properties physical state: liquid color: colorless to light yellow odor: slight odor threshold: not available. ph: 7 vapor pressure: not available. boiling point/range: > 200 c (> 392f) supplier method melting point/ range: not available. specific gravity: 1.17 vapor density: not available. flash point: > 200 c (> 392f) supplier method flammable/explosive limits - lower: not available. flammable/explosive limits - upper: not available. autoignition temperature: not available. evaporation rate: not available. solubility in water: insoluble partition coefficient (n-octanol/water): not available. voc content: not available. viscosity: 9,500.00 - 12,000.00 mpa.s 10. stability and reactivity stability : stable under normal conditions of storage and use. hazardous reactions: none under normal processing. polymerization may occur at elevated temperature or in the presence of incompatible materials. hazardous decomposition products: oxides of carbon. oxides of nitrogen. irritating vapours. incompatible materials: strong acids, alkalies and oxidizing agents. conditions to avoid: excessive heat. store away from incompatible materials. 11. toxicological information hazardous components ntp carcinogen iarc carcinogen osha carcinogen (specifically regulated) epoxy resin no no no hazardous components health effects/target organs epoxy resin allergen, irritant 12. ecological information ecological information: not available.
idh number: 1188169 product name: eccobond 45 clr 1# individual page 4 of 5 13. disposal considerations information provided is for unused product only. recommended method of disposal: follow all local, state, federal and provincial regulations for disposal. hazardous waste number: not a rcra hazardous waste. 14. transport information u.s. department of transportation ground (49 cfr) proper shipping name: not regulated hazard class or division: none identification number: none packing group: none international air transportation (icao/iata) proper shipping name: environmentally hazardous substance, liquid, n.o.s. (epoxy resin) hazard class or division: 9 identification number: un 3082 packing group: iii water transportation (imo/imdg) proper shipping name: environmentally hazardous substance, liquid, n.o.s. (epoxy resin) hazard class or division: 9 identification number: un 3082 packing group: iii marine pollutant: epoxy resin 15. regulatory information united states regulatory information tsca 8 (b) inventory status: all components are listed or are exempt from listing on the toxic substances control act inventory. tsca 12(b) export notification: none above reporting de minimus cercla/sara section 302 ehs: none above reporting de minimus cercla/sara section 311/312: immediate health cercla/sara 313: none above reporting de minimus california proposition 65: no california proposition 65 listed chemicals are known to be present. canada regulatory information cepa dsl/ndsl status: all components are listed on or are exempt from listing on the canadian domestic substances list. 16. other information this material safety data sheet contains changes from the previous version in sections: new material safety data sheet format. prepared by: nicole laput, regulatory affairs specialist
idh number: 1188169 product name: eccobond 45 clr 1# individual page 5 of 5 disclaimer: the data contained herein are furnished for in formation only and are believed to be reliable. however, henkel corporation does not assume responsibility for any results obtained by persons over whose methods henkel corporation has no control. it is the user's responsibility to determine the su itability of henkel's products or any production methods mentioned herein for a particular purpose, and to adopt such precaution s as may be advisable for the protection of property and persons against any hazards that may be involved in the handling and use of any of henkel corporation's products. in light of the foregoing, henkel co rporation specifically disclaims all warra nties, express or implied, including warranties of merchantability and fitness for a particular purpose, arising from sale or use of henkel corporation's products. henkel corporation further disclaims an y liability for conse quential or incidental damages of any kind, including lost profits.
|
